DIY Stompbox Gallery
This is Grind Custom's other Chimera v3 PCB, this time the buffered one.
Not much more to say really, it's another Klone.
...and another two. People seem to be rabid for them again since the KTR came and went. Well it (almost) keeps us in capacitors anyhow.
Small Klone II
Sune decided it was time to try one of these Klone things out, so this was built for him. It's Jimmy's (Beejive Pedals) mental Apis board, again fettled to be buffered bypass.
Nope, it's not in a 1590A. I really wasn't kidding when I said I wasn't doing any more ultra-ickle ones ;)
This is Grind Custom's Chimera v3 PCB. Which is an updated version of Rej's a true bypass Klone.
I'm really rather pleased with this one. It's been a while since I knocked out a Klone and this one on the new board was a joy to build and again stands up to blind listening against our referece Klone. Smashing!
...and two more. Can you tell we're in a fairly major deficit right now when it comes to the pedal fundage?
I thought I'd throw a couple of notes in to this section just to document the only change we make to them and what diodes we use. Just to debunk the unicorn tears you understand as this is a completely replicatable pedal.
The cap that we change is C15 which goes to pin 2 of the tone pot. On the original schematic, and indeed likely on the original pedal that was de-gooped and traced, this is a 3n9. When Phil brought his Klon over to compare to (right at the bottom of this page, this was very early on and all subsequent Klones have this change), ours was missing some mids. We chopped and changed until we settled on an 8n2. At that point it was indistinguishable from Phil's Klon.
The other point of contention are the 'essential' diodes. Most germs work to be fair if you get them with a forward voltage of 260-290mV. We've found that 1N34As seem to be the closest and source ours from Tayda. The last couple of batches we've had have all been in range. But meter them regardless to check.
What it's based on: Klon Centaur
JimmyBJJ's utterly insane miracle of miniturisation that is his Apis PCB. Yep this is a Klone in a 1590A. *doffs cap* impressive sir, most impressive!
The other one has had buffered bypass added on making the build a complete pain. It seemed like a good idea at the time... For those interested this is how:
The centaur has gone red as it was left on a window sill for some time. Looks like the ink ain't UV friendly!
As noted below, this is my Madbean Sunking based colourful Klone rebuilt in standard Klone form and rehoused to flog.
I rebuilt it in a new enclosure mainly for neatness and shiny newness. The way we finish pedals now is much more durable too. Also because not many people liked the colourful Klone decal...
It seems it's Klone season again (seeing as the KTR is now out of production). This one has come about by chance. I was over at Martin's (MJW Amplification) doing amp stuff and he gave me a surplus Madbean Sunking board he had. So I decided to build myself a smaller Klone.
My old Klone will be popping back up here shortly as I'm rebuilding it and will be flogging it in the surplus stuff for sale section.
This is Grind Custom's Chimera PCB. Which is essentially a true bypass Klone. Number four and five look a little different because they've had the buffered bypass added back in which the board wasn't really designed for. So they're not quite as pretty. But those two are now essentially Klones rather than Klonishes...
There is a fractional difference between buffered bypass and true bypass when it comes to the sound of this effect. So little that it's not really worth speaking about. But for those that it matters to, this is indistinguishable from our remaining Sunking baseline pedal (one of the two that was back-to-backed with a Centaur).
I bought the boards because, as you can probably tell, it's the pedal I get asked to build more than anything else. So when Rej offered a few for sale, I grabbed a handful. But it seems I've saturated my very small corner of the market (ie friends from the BKP forum) and I had them all surplus. So I built them up and stuck them on eBay.
Kingslayer Rise! / Klone Slayer
What it's based on: Madbean Kingslayer
Ah Madbean's Kingslayer, how we've waited for thee! It's essentially a Klon with all the oddness engineered out and with some sensible stuff added in. The whole circuit now runs charge pumped, not just the last stage as was the case with the original. He's also added switchable clipping in the feedback loop and selectable regular clippers (which can be bypassed completely if you prefer the others).
The result: It's not a Klon anymore. It's certainly got more headroom and is voiced slightly differently. Personally I prefer it, it's the genuine upgrade that the KTR should have been. The Klon is dead, long live the King!
I suppose I should say something about the decal. Yep, it's Eddie (The Trooper). Which has nothing at all to do with slaying kings. Indeed it's about the charge of the Light Brigade, but it's a cool picture that fit really well.
The Klone Slayer is for John (Loopie of TGP). This one is buffered bypass and, as the power jack in the top didn't allow for easy placement of the clipping switches, we've fitted jumpers internally instead. Which is actually a really neat way of doing this.
A little bit more Klone action thanks to gtrplaya101 on BYOC having a re-run of his Klone boards of which I managed to snag four before they all were snapped up. These are proper clones like the original Sunking, rather than a work-a-like like the MKC1.
The first goes to Don (D1DSJ). Like a plank, I drilled the stomp too close to the edge to get a battery in. Doh! I suppose it has been quite a while since I built one of these.
Second, with the battery provision sorted and things swapped around to fit better with this slightly larger board (you'll notice gain and vol are swapped now) is for Jean-Claude (Viking).
Number 3 is for Ole (Kiichi).
Number 4 went to Colin (Blue).
With Madbean stopping doing the Sunking boards this is a MKC1 board from GuitarPCB.com with a load of substituted parts along the lines of the Klones we've done. The interesting thing is that dispite it now being true bypass and the buffer running at 9v rather than charge pumped, it sounds nigh on the same. There is a little bit of noise when the pedal is completely dimed. Interestingly the original Klones did this too, but it's not quite as apparent. You never run them that way anyhow.
Is this the future of Klones? Don't know yet. It's certainly an option though. It's not quite as compact or as neat to wire as the original Klone. But it's got the tone.
Oh and love the finish on this one. Cleggy has been experimenting once again. This is polished, decalled, then the top has been coated in Envirotex, but not the sides. I think it looks bloody brilliant.
This one is going, along with a Darkside, to Andrew W of the BKP forum in exchange for a project Telemaster for me to play with. Sweeet.
Klonish 2 (actually 2 & 3, the were nigh on identical so I only took one set of pics) are for Wez and Huw. Same as above but made with the last of our ribbon cable. I wish I could source this stuff, it's brilliant. Very high quality Hitachi pre-bonded 24AWG ribbon. Ideal for pedals. Can't seem to find it anywhere (this lot was scavenged from an old hifi).
Built for Dave (Twinfan) on one of Madbean's awesome Sunking PCB. I desperately wanted this one not to live up to the hype... *sighs* Looks like I'll be making me one.
There were some defects in the casting that we didn't catch until after the decal was applied which show through. In certain light it's more apparent. Bit annoying really, but to correct it would have meant stripping it and starting again.
Update 1: Colourful Klone is mine.
Update 2: Silver Klone is Phil's. Temporoary Telecaster knobs on it.
Update 3: Klo(w)n? is Shaun's.
Update 4: Silver Klone 2 is Gary's.
Update 5: ...and another two (only one pictured as they're the same), possibly the neatest yet. They're actually second pedals for both Phil and Dave. After a back-to-back with Phil's Centaur we've made a cap change to the Klone to make it sound near as damnit identical to Phil's pedal. It thickens it up quite a bit.
FWIW I'm not saying it's identical to all of them. Analogue electronic part variances/tolerances being what they are. But we could flip them back and forth and not know which was on against his particular pedal.
[ back ]